A Review On Variation In Differential Gearbox Design and Its Materials

Authors

  • Anand Pali Department Of Mechanical Engineering S.S.S.U.T.M.S, Sehore M.P.
  • Prof.Sanjay Kalraiya Department Of Mechanical Engineering S.S.S.U.T.M.S, Sehore M.P.

Keywords:

Differential Gear Box, Static Structural Analysis, Design and Structural Analysis, Aluminum Alloys Grade

Abstract

The primarily objective of this research to design CAD model &
perform the static structural analysis of differential gear box of three different
grades of Aluminum Alloys that are “AA5182, AA6061 & AA7108” iterated at
three different magnitude of torque value that are 190N-m, 235N-m & 320N-m, to
calculate the total deformation & equivalent stress value for each. This paper will
also show that among these three alloys which one is the light & helps to reduce
the weight of vehicle. To design the CAD model in CATIA v5 & for the static
structural analysis ANSYS 15.0 has been used.

References

N. Siva Teja., K. Dinesh Babu., M. Siva Nagendra., Ch. Phanideep., J. Sai Trinadh. Design and analysis of differential gear box in

automobiles, International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 5, May 2017.

N.Vijayababu., Ch.Sekhar. Design and analysis of differential gear box used inheavy vehicle. International Conference on Recent Trends in

Mechanical Engineering-2K15(NECICRTME-2K15), 20th – 21st November. 2015.

P.Vinay, Ch., Venkata Satya Sri Vamsi., M.Hemanth., A.Saiteja., Mohammad Abid Ali & P. Ashok Kumar. Design and simulation of

mems based accelerometer for crash detection and air bags deployment in automobiles. International Journal of Mechanical Engineering

and Technology (IJMET) Volume 8, Issue 4, April 2017

K. Sunil Kumar., Dr. Sumathy Muniamuthu., S. Arun & A. Mohan. Experimental analysis of noise and vibration reduction in windmill gear

box for 5mw wind turbine. International Journal of Mechanical Engineering and Technology (IJMET) Volume 7, Issue 6, November–

December 2016.

G. Srikanth Reddy & M. Promod Reddy. Evaluation on failure of an automobile differential gear box. International Journal of Latest Trends

in Engineering and Technology Vol.(8)Issue(3) 2015.

Ronak P Panchal 2015. Evaluation on Failure Analysis of an Automobile Differential Pinion Assembly. IJIRST –International Journal for

Innovative Research in Science & Technology| Volume 1 | Issue 12 | May 2015.

Sachindra Kumar., Anjani Kumar Singh., Nitesh Kumar., Sushil Patel & Ajit Kumar.Transmission error analysis of involute gears in mesh

by FEM. Volume : III, Issue : VII, July – 2014.

Luciana Sgarbi Rossino. Surface Contact Fatigue Failure of a Case Hardened Pinion Shaft. Materials Research. 2014.

I.Barsoum. Analysis of the torsional strength of hardened splined shafts. https://doi.org/10.1016/j.matdes.2013.08.020 Volume 54, February

Samareh Mohammadzadeh Polami. Joint-site structure friction welding method as a tool for drive pinion light weighting in heavy-duty

trucks journal of Materials Processing Tech. 2014.

S. H. Gawande, S.V. Khandagale, V. T. Jadhav, V. D. Patil & D. J. Thorat. Design, Manufacturing & Analysis of Differential Crown Gear

and Pinion for MFWD Axle. IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE).2013

Grégory Antoni. On the Mechanical Friction Losses Occurring in Automotive Differential Gearboxes. The Scientific World Journal

Volume 2014

Daniel Das.A. Structural Analysis of Differential Gearbox., JIET, April 2013, Vol.2 issue 2.

S. Puttaswamaiah, Dr. J.N. Prakash and K.B. Kiran. Finite Element Stress Analysis of Spur Gear and Evaluation of Transmission Error.

international Conference on Challenges and Opportunities in Mechanical Engineering, Industrial Engineering and Management Studies 55

(ICCOMIM - 2012), 11-13 July, 2012.

Dr.-Ing. T. Schulze. Calculation of Load Distribution in Planetary Gears for an Effective Gear Design Process. AGMA Technical Paper

Downloads

Published

31-12-2017

How to Cite

Anand Pali, & Prof.Sanjay Kalraiya. (2017). A Review On Variation In Differential Gearbox Design and Its Materials. International Journal for Research Publication and Seminar, 8(8). Retrieved from https://jrps.shodhsagar.com/index.php/j/article/view/1228

Issue

Section

Original Research Article